Tweet
Zomaar wat uitspraken van Ui himself over de X32,
staan best wel wat leuke weetjes in over de gebruikte onderdelen etc.
While I cannot speak on behalf of competitors whose consoles fail, I can assure you that we have not spared any effort to test the X32. In fact we spent over one year to vigorously test the X32 under any possible condition and there are reports that a tester even left his X32 in the car overnight while it was exposed to freezing temperatures. After switching it on, it worked perfectly fine.
This is the main reason why we delayed the release of the X32 as we took extreme measures to make sure the console is mature.
Six months ago, we handed out over 20 consoles to professional rental companies and power users with the mission to find software bugs and propose suggestions for improvements.
Christian Boche who is an avid contributor here, is a witness to that process and we are extremely grateful for his invaluable input and the feedback we received from all other testers.
Thanks to reports from some forum members we have been made aware of a noise issue affecting certain X32 consoles. The issue is generally reported as increased noise on channels 16 and 32.
Since the first report of this issue we have obtained one of the affected consoles and identified both the source of the noise and the relatively simple fix. During production a limited number of consoles were wired with an internal cable improperly routed too close to the mic preamp boards, resulting in the inducted noise from the control cables.
Properly rerouting the short cable solves the issue permanently.
We will soon post a service advisory how to address the issue and will make this right.
Uli
Why is the X32 so affordable?
This is such an important question because there is a lingering perception that we must somehow be cutting corners to reduce cost. I have seen people claim that we must be using poor quality parts, not following quality control processes or somehow designing in obsolescence. While I can tell you that this is absolutely not the case, it may be best if I offer some insights into our business model to explain.
There are four fundamental elements that comprise the selling price of our products; materials, labor, overhead and profit. Achieving low prices and delivering great value for our customers requires great discipline and hard work in each of these areas. It is my responsibility as the CEO to set the pace and ensure that we reduce costs while always increasing quality; because without quality, we cannot maintain low costs.
We reduce the cost of raw materials in two ways; first, we buy direct from manufacturers and not through a second source, distributor or contract manufacturer. Second, we buy in enormous quantities and leverage this volume in negotiating lower prices. Of course owning the factory where we build our products allows us to cut out at least 30% of the margin demanded by contract manufacturers who are supplying some of our competitors.
Consider that we buy our A/D and D/A converters from Cirrus Logic; the same parts (CS5368 and CS4385) that you will find in a $200k console; we encourage anyone interested to look further into this. We have also been told that we are the single largest Cirrus Logic customer behind only Apple! You will find similar examples with Analog Devices, makers of the SHARC DSPs that we use or Mabuchi, who make the motors for our motor-faders (and those of Penny & Giles, Alps etc.) and the list goes on. We are buying the very best parts, from the very best manufacturers, direct and in huge quantities. That means we pay the lowest possible prices.
Likewise we have two major ways in which we reduce the cost of labor to build our products. First, we own the factory and this means we are paying workers directly and not through a third party that is making a markup. Again, this results in up to 35% savings. Second, we have invested in massive amount of automation to a far greater extent than many in China in order to reduce cost while increasing quality.
This past year for example we converted the placement of electrolytic capacitors from hand-insertion to full automation. Each of the machines that now place e-caps in rapid-fire succession cost over $500k US so the savings in cost will take some time to be realized. But we have seen an immediate improvement in first-pass yield by eliminating the chance of human error, and that is both improving quality and reducing the cost of re-work.
We run our company with a very low overhead relative to some competitors, and we do this not by cutting corners but rather by working smarter. First off we invest heavily in systems that improve productivity and reduce redundancy. For example our engineering management software Agile talks to our website content management system so when we enter a product’s specifications we do it once and it is automatically replicated across several departments and is immediately posted to the web. Or take our service manuals which are created automatically, in real-time and with the very latest schematics, parts lists and engineering changes - all available through an on-line portal.
Another way we reduce overhead is by re-investing profits in our company to purchase machinery, land and buildings. For example we have purchased new buildings in Manchester, UK and Las Vegas, USA in the past year. We have also purchased land and we are building a $60 million state-of-the-art campus to contain a new factory, research center, logistics hub and residential village in China. These investments not only give us greater control over quality and production but they also reduce our operating costs over the long term.
Finally it is important to know that we operate on what would be considered to be a slim margin by industry standards. While some manufacturers price their products according to what they think the market will accept, we do it very differently. We calculate our costs and add a fair markup that will allow us to continue to grow our business and nothing more. Again, we have all seen strategies where manufacturers release new products at high prices only to reduce them as other competitors come into the market. We prefer to offer a fair price from the beginning and not play such games.
The reality of our company is that we are a highly efficient organization of 3,500 people including over 250 engineers and in-house manufacturing. We build up to 5 million products a year and consequently buy parts at the lowest possible cost. Plus, our quality is among the best in the world, with a defect rate of well under 0.7%, allowing us the confidence to offer a 3-year warranty.
Yes, we are a very different kind of company, we want to be different and I am immensely proud of our team.
staan best wel wat leuke weetjes in over de gebruikte onderdelen etc.
While I cannot speak on behalf of competitors whose consoles fail, I can assure you that we have not spared any effort to test the X32. In fact we spent over one year to vigorously test the X32 under any possible condition and there are reports that a tester even left his X32 in the car overnight while it was exposed to freezing temperatures. After switching it on, it worked perfectly fine.
This is the main reason why we delayed the release of the X32 as we took extreme measures to make sure the console is mature.
Six months ago, we handed out over 20 consoles to professional rental companies and power users with the mission to find software bugs and propose suggestions for improvements.
Christian Boche who is an avid contributor here, is a witness to that process and we are extremely grateful for his invaluable input and the feedback we received from all other testers.
Thanks to reports from some forum members we have been made aware of a noise issue affecting certain X32 consoles. The issue is generally reported as increased noise on channels 16 and 32.
Since the first report of this issue we have obtained one of the affected consoles and identified both the source of the noise and the relatively simple fix. During production a limited number of consoles were wired with an internal cable improperly routed too close to the mic preamp boards, resulting in the inducted noise from the control cables.
Properly rerouting the short cable solves the issue permanently.
We will soon post a service advisory how to address the issue and will make this right.
Uli
Why is the X32 so affordable?
This is such an important question because there is a lingering perception that we must somehow be cutting corners to reduce cost. I have seen people claim that we must be using poor quality parts, not following quality control processes or somehow designing in obsolescence. While I can tell you that this is absolutely not the case, it may be best if I offer some insights into our business model to explain.
There are four fundamental elements that comprise the selling price of our products; materials, labor, overhead and profit. Achieving low prices and delivering great value for our customers requires great discipline and hard work in each of these areas. It is my responsibility as the CEO to set the pace and ensure that we reduce costs while always increasing quality; because without quality, we cannot maintain low costs.
We reduce the cost of raw materials in two ways; first, we buy direct from manufacturers and not through a second source, distributor or contract manufacturer. Second, we buy in enormous quantities and leverage this volume in negotiating lower prices. Of course owning the factory where we build our products allows us to cut out at least 30% of the margin demanded by contract manufacturers who are supplying some of our competitors.
Consider that we buy our A/D and D/A converters from Cirrus Logic; the same parts (CS5368 and CS4385) that you will find in a $200k console; we encourage anyone interested to look further into this. We have also been told that we are the single largest Cirrus Logic customer behind only Apple! You will find similar examples with Analog Devices, makers of the SHARC DSPs that we use or Mabuchi, who make the motors for our motor-faders (and those of Penny & Giles, Alps etc.) and the list goes on. We are buying the very best parts, from the very best manufacturers, direct and in huge quantities. That means we pay the lowest possible prices.
Likewise we have two major ways in which we reduce the cost of labor to build our products. First, we own the factory and this means we are paying workers directly and not through a third party that is making a markup. Again, this results in up to 35% savings. Second, we have invested in massive amount of automation to a far greater extent than many in China in order to reduce cost while increasing quality.
This past year for example we converted the placement of electrolytic capacitors from hand-insertion to full automation. Each of the machines that now place e-caps in rapid-fire succession cost over $500k US so the savings in cost will take some time to be realized. But we have seen an immediate improvement in first-pass yield by eliminating the chance of human error, and that is both improving quality and reducing the cost of re-work.
We run our company with a very low overhead relative to some competitors, and we do this not by cutting corners but rather by working smarter. First off we invest heavily in systems that improve productivity and reduce redundancy. For example our engineering management software Agile talks to our website content management system so when we enter a product’s specifications we do it once and it is automatically replicated across several departments and is immediately posted to the web. Or take our service manuals which are created automatically, in real-time and with the very latest schematics, parts lists and engineering changes - all available through an on-line portal.
Another way we reduce overhead is by re-investing profits in our company to purchase machinery, land and buildings. For example we have purchased new buildings in Manchester, UK and Las Vegas, USA in the past year. We have also purchased land and we are building a $60 million state-of-the-art campus to contain a new factory, research center, logistics hub and residential village in China. These investments not only give us greater control over quality and production but they also reduce our operating costs over the long term.
Finally it is important to know that we operate on what would be considered to be a slim margin by industry standards. While some manufacturers price their products according to what they think the market will accept, we do it very differently. We calculate our costs and add a fair markup that will allow us to continue to grow our business and nothing more. Again, we have all seen strategies where manufacturers release new products at high prices only to reduce them as other competitors come into the market. We prefer to offer a fair price from the beginning and not play such games.
The reality of our company is that we are a highly efficient organization of 3,500 people including over 250 engineers and in-house manufacturing. We build up to 5 million products a year and consequently buy parts at the lowest possible cost. Plus, our quality is among the best in the world, with a defect rate of well under 0.7%, allowing us the confidence to offer a 3-year warranty.
Yes, we are a very different kind of company, we want to be different and I am immensely proud of our team.
??!!??
Comment